SYNTECH PAVIDAMP

Three-component anti-humidity epoxy base, in aqueous emulsion

Code: SYN.0096

Components: 3

Appearance: Liquid + Powder

Three-component formulation based on liquid epoxy resins in aqueous emulsion and hydraulic binders, specially designed for use as a base for cement surfaces even in the presence of humidity and in conditions of hydraulic negative pressure.

Certification obtained and Standards

Product of the Floor line, the line of products from Azichem Srl dedicated to the main, complementary products and accessories for the construction, restoration and/or renovation of concrete floors and screeds.

Floor - Prodotti per pavimenti e massetti in calcestruzzo

Product of the Floor line, the line of products from Azichem Srl dedicated to the main, complementary products and accessories for the construction, restoration and/or renovation of concrete floors and screeds.

General characteristics

shelf-life

Shelf-life: 6 months

use-wearing-protective-gloves

Use wearing protective gloves

temperature-of-use

Temperature of use: +8 / +35 °C

solvent-free

Solvent-free

uv-resistant

UV-resistant

pot-life

Pot-life: 45 min

density

Density: 1.75 (± 0.05) kg/dm³

adhesion-to-the-substrate

Adhesion to the substrate: >3.5 N/mm²

min-recommended-thickness

Min. recommended thickness: 3 mm

Technical specifications

Hard to touch

25 - 35 min

Dry residue

75 %

Mixing ratio of the components

100:28:125 _

Complete hardening

7 - 8 h

Available colours

- White

Packaging and dimensions

- Can 4 kg [A]

- Can 1.12 kg [B]

- Pail 5 kg [C]

- Kit: 1 Can 4 kg [A] + 1 Can 1.12 kg [B] + 1 Pail 5 kg [C]

- Can 8 kg [A]

- Can 2.25 kg [B]

- Pail 10 kg [C]

- Kit: 1 Can 8 kg [A] + 1 Can 2.25 kg [B] + 1 Pail 10 kg [C]

Consumption

From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered.

Use fields

Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out.

Preparation of supports

The support must be appropriately cleaned manually and/or mechanically in order to eliminate non-adhering or loose parts, and any encrustation, efflorescence, dust, fatty substances, residues from previous coatings, etc.

Use method

Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained.

If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports.

If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m².

If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m².

Application methods

- Brick trowel

- Brush

- Paint roller

Tool cleaning

- Thinner for resins

Permitted supports

- Concrete

- Prefabricated concrete

- Floor screed

Warnings, precautions and Ecology

Do not apply the product on wet bases.

Share

Products on display

  • Floortech Prerit
  • Protech Balcony
  • Syntech H.A.G.