Appearance: Powder + Liquid
Two-component waterproofing cement, in aqueous dispersion, deformable, plasto-elastic. Particularly indicated for waterproofing terraces and balconies before the installation of tile or brick flooring.
Specification for Mortar for Masonry - General purpose rendering/plastering mortar (GP)
Suitability to contact with drinking water (Quality of water intended for human consumption)
D.M. 06/04/2004, n. 174
Regulation concerning materials and objects that can be used in fixed systems for the collection, treatment, adduction and distribution of water intended for human consumption.
Shelf-life: 12 months
Pot-life: 60 min
Suitable for contact with drinking water
Temperature of use: +8 / +30 °C
Mixing ratio: 3:1 _
Maximum diameter of aggregate: 0.4 mm
Permeability to water vapor
Mixing ratio of the components
Longitudinal elongation at break
Bridging capacity on wide cracks
- Bag 24 kg [A]
- Plastic can 8 kg [B]
- Pallet: 50 x (Bag 24 kg [A])
- Pallet: 50 x (Plastic can 8 kg [B])
- Kit: 1 Bag 24 kg [A] + 1 Plastic can 8 kg [B]
OSMOCEM FLEX is certified for compatibility with contact and containment of drinking water and food substances (certificate n. 04/2010 of the Laboratorio Analysis Service di Settimo di Pescantina - VR).
Two-component professional product. Proportioning of component A + component B specially designed to give the installer certainty of the result and guarantee of impeccable work: the tank of component B (8 kg) contains slightly more compared to the quantity necessary for mixing the bag (24 kg), allowing the installer, before laying the product, to withdraw from the tank up to 1 lt of the special resin of component B, dilute with 1 lt of water and use this aqueous emulsion to prime the application support; in this way at least three extraordinarily effective operations are performed with a simple and rapid priming: a) expulsion of the air from the superficial porosity _fillers (with drastic reduction of the well-known blisters that occur on low thickness elastic products); b) reduction of the support absorption (to guarantee a suitable setting of the waterproof finish); c) increase in adhesion thanks to the deep penetration of the polymeric component.
Approximately 1.8 kg/m² of OSMOCEM FLEX for each millimetre of thickness to be made.
Moisture-proofing concrete containment works (tubs, swimming pools, pipes, ducts, areas containing food, etc.). Moisture-proofing balconies, terraces, bathrooms, showers, etc., prior to laying successive plasters and screeds, ceramic coatings provided they are sufficiently porous and absorbent and free from any waterproofing and / or water-repellent surface treatment, whether chemical (siloxanes, epoxies, polyurethanes, etc.) or natural (wax-up). Waterproofing coating of earth-retaining masonry, micro-cracked plaster. Deformable finishing coats in general.
Application surfaces should be clean and free of dust, soiling, crumbling and non-adhering parts, etc., water repellent treatments in general, etc. conveniently saturated with water until they reach the condition "saturated with dry surface".
Any cracks from plastic or hygrometric shrinkage present should be preliminarily treated with appropriate products and techniques. In the case of extended coating surfaces you must provide appropriately placed "chimney flues" for venting steam.
OSMOCEM FLEX comes in two predosed components that must be thoroughly mixed, with mixers with a low number of revolutions (maximum. 300 Revs/minute) until a homogeneous lump-free mixture is obtained. The addition of other ingredients should be absolutely avoided. The tank of component B (8 kg) contains slightly more compared to the quantity necessary for mixing the bag (24 kg), allowing the installer, before laying the product, to withdraw from the tank up to 1 lt of the special resin of component B, dilute with 1 lt of water and use this aqueous emulsion to prime the application support (see also the ADDITIONAL INFORMATION section). In case of exceptionally arid climate, it is possible to make moderate consistency corrections, where necessary, adding water up to a maximum of 8%.
When waterproofing terraces and balconies, two coats, each about 1.5 mm thick (2.2 kg/m² per coat), of OSMOCEM FLEX should be applied, each coat should be applied when the previous one looks stable (at least 4 hours later at 20°C). It is recommended to interpose the fibreglass alkaline-resistant mesh ARMAGLASS 160 in the thickness of OSMOCEM FLEX, between the first and second coat. The self-adhesive butyl band PROBAND should also be placed between the floor screeds and the elevation walls. Finally, it is advisable to place the special elastic band ELASTOTEX 120 or ELASTOTEX 120 CLOTH, at any expansion joints, securing it with the same OSMOCEM FLEX.
- Plastering machine
- Paint roller
- Scrubbing brush
- Floor screed
Do not use OSMOCEM FLEX on strongly degraded or non-adhering supports , since it would reduce the waterproofing quality.
Do not apply on little or non-porous substrates or previously coated with water-repellent treatments in general, if not after appropriate roughening by bush hammers, sanders and equipment suitable for preparatory treatments of substrates, or after appropriate treatment with suitable polymeric primers.
Monocomponent, osmotic cement mainly used to fill and waterproof the cavities in a concrete wall having removed the protruding part (excess) of the formwork spacers.
Two-component, osmotic cement, certified for drinking water and EN-14891. Moderately deformable, highly resistant and adhesive, it is a multi-use product. Resists traffic, UV rays, ideal for reinforced finishing coats. Azichem's bestseller!
Hard, monocomponent, osmotic cement. Highly resistant and adhesive. Specifically for the construction of reinforced, impermeable and thick grout, both in thrust and counter-thrust.
Hard, monocomponent, osmotic cement, certified for drinking water. Very adhesive and easy to apply. It is a classic osmotic mix, efficient and cheap!
Two-component, osmotic cement, slightly deformable. To use thick, both in thrust and counter-thrust. It is the evolution of the OSMOCEM MR, easier to apply and more adhesive. Recommended!
Hard, monocomponent, osmotic cement with a natural hydraulic lime base. It is an ideal product for waterproofing in positive thrust, in the restoration and recovery of old buildings.
Rigid monocomponent osmotic cement with reactive crystallizing reaction. Specific for the construction of waterproof, thick coatings, both in thrust and in counterthrust, of products with liquid contents at pH 4.5.